¶ Appliance Front Panels
- Front Panel combined with the appliance on the back.
- Inside Corner Radius: 35mm
- The "Installation Width" and "Cabinet Height" can be modified
- *Please Note: The Appliance Installation Width MUST follow the Appliance Spec Requirement
- The "Actual Panel Width" and "Actual Panel Height" can be modified
- *Please Note: We recommend to follow us standard reveal on the cabinet, to ensure the door alignment. As default, the appliance front panel dimension has been set to match with the cabinet door size.
- Panel Reveal will be calculated automatically, and can not be modified.
¶ Appliance Front Panels with Center Cut-out
- Front Panel combined with the appliance on the back.
- The "Installation Width" and "Cabinet Height" can be modified
- *Please Note: The Appliance Installation Width and Height MUST follow the Spec Requirement
- The "Actual Panel Width" and "Actual Panel Height" can be modified
- *Please Note: We recommend to follow us standard reveal on the cabinet, to ensure the door alignment. As default, the appliance front panel dimension has been set to match with the cabinet door size.
- Top, Bottom, Left, and Right Distance can be modified based on the spec requirement.
¶ Basic Base Panels
¶ PNL_SIDE
⇡ Front & Back Overlay (Auto) (¾” Door thickness + ⅛” Door Bumper)
- Use as base cabinet side panel.
- ⅞” overlay on the front edge of the panel, flash with the cabinet door.
- Panel depth needs to be the ⇣same as the cabinet carcass depth. System will automatically add the overlay.
1” Depth Oversize (Default) ⇡
1” Height Oversize (Default) ⇡
- 1” Depth Oversize as standard, on the back edge of the panel. Contactor MUST trim the panel on the jobsite inorder for the panel to install flush to the door, without living a gap in behind the panel.
- 1” Height Oversize as default. Contactor MUST trim the panel on the job site
¶ ISLAND_SIDE
⇡ Front & Back Overlay (Auto) (¾” Door thickness + ⅛” Door Bumper)
- Use as island side panel.
- ⅞” overlay on BOTH front and back edge of the panel, flash with the cabinet door, and the island back panel.
- Panel depth needs to be the same as the cabinet carcass depth. System will automatically add the overlay.
- NO oversize depth, since the width of this panel CANNOT be trimmed on the job site.
1” Height Oversize (Manual) ⇡
- NO oversize depth, since the width of this panel CANNOT be trimmed on the job site.
- 1” Height Oversize as default. Contactor MUST trim the panel on the job site.
¶ PNL_BACK
- Use as island back panel.
- NO overlay on all edges.
- NO oversize width as default. Can be added manually if needed.
- No oversize height as default. If panel needs to be installed attached to the floor, 1” height oversize must be added manually.
¶ PNL_FRONT
- Use as custom panel for panel-ready appliance.
- Reveal value can be changed based on the design need.
- Comes with standard top, bottom, left, and right reveal. ⇣ Same reveal as the standard base cabinet.
¶ Wall Panels & Tall Panels
 |
 |
¶ PNL_WALL_SIDE
⇡ Front Overlay (¾” Door thickness + ⅛” Door Bumper)
- Use as wall cabinet side panel.
- ⅞” overlay on the front edge of the panel, flash with the cabinet door.
- Panel depth needs to be the ⇣ same as the cabinet carcass depth. System will automatically add the overlay.
1” Height Oversize (Default) ⇡
1” Depth Oversize (Default) ⇡
- 1” Depth Oversize as standard, on the back edge of the panel. Contactor MUST trim the panel on the jobsite inorder for the panel to install flush to the door, without living a gap in behind the panel.
- 1“ Height Oversize as default. Contactor MUST trim the panel on the job site
¶ Design Tips
- Any panels that will have the back edge attached to the wall, MUST have Depth oversize
- Any panels that will have the top / bottom edge attached to the ceiling / floor, MUST have Height oversize
- The contractor is required to trim the oversized panel on the job site to achieve optimal installation results, making sure there are no gaps between the panel and the wall, ceiling, or floor.
¶ PNL_FRONT_GOLA
- Base Front Panel with GOLA
- For ADA Compliant Appliance ONLY (Height less than 32 1⁄4”)
- Panel Height = Cabinet body Height (With standard reveal)
- Appliance Height = 32 1⁄4”, can NOT be modify
- For correct design, gap in between Gola and Appliance
- For incorrect design, Gola collide with Appliance
- Error Message: GOLA COLLISION